737 Single Control Head

This page lists all the hardware and electrical components required. 

These units can be produced on a standard 3D printer bed size of 220 x 220mm.

Single Control Yoke Components Required:

m6-stainless-steel-dome-head-bolts-12-20

Dome head Machine Screws

M4 x 22mm (QTY 1)

M4 x 25mm (QTY 1)

M4 x 30mm (QTY 2)

M4 x 20mm (QTY 1)

M4 x 35mm (QTY 2)

M4 x 40mm (QTY 2)

hellical-springs-500x500 (1).jpg

3" Expansion Spring

QTY 1

countersunk-flat-head-screw-800x800.jpg

Countersunk head Machine Screws

M4 x 10mm (QTY 1)

download (5).jpeg

RV24YN 20S

HQ POT 10K Ohm

QTY 1

6203 Bearing.png

BEARING

(6001) 

Inner Dimension: 12mm 

Outer Dimension:

 28mm 

Width:

8mm 

QTY 1

Builder-PLA-Black-4.5kg-1280x720-1280x72

Dark Grey PLA

QTY 1 Roll

6203 Bearing.png

BEARING

(6203)

Inner Dimension: 17mm

Outer Dimension: 40mm

Width:

12mm

QTY 2

Print Guide

RH BODY

(1)

Support: ON

Adhesion: Brim 10mm

Nozzle: 0.4mm 

Speed: 50mm/s

Layer Height: 0.1mm

Infill:25%

YOKE SHAFT

(5)

Support: On

Adhesion: BRIM 10mm

Nozzle: 0.4mm

Speed: 50mm/s

Layer Height: 0.2mm

Infill:100%

LH BODY

(2)

Support: ON

Adhesion: Brim 10mm

Nozzle: 0.4mm 

Speed: 50mm/s

Layer Height: 0.1mm

Infill:25%

SPACER

(6)

Support: OFF

Adhesion: Brim 10mm

Nozzle: 0.4mm

Speed: 50mm/s

Layer Height: 0.1mm

Infill: 25%

NOGGIN

(3)

Support: Off

Adhesion: Skirt

Nozzle: 0.4mm

Speed: 50mm/s

Layer Height: 0.2mm

Infill:25%

SPUR GEAR

(7)

Support: Off

Adhesion: SKIRT

Nozzle: 0.4mm

Speed: 50mm/s

Layer Height: 0.1mm

Infill:25%

YOKE LOCK

(4)(

Support: Off

Adhesion: Skirt

Nozzle: 0.4mm

Speed: 50mm/s

Layer Height: 0.2mm

Infill:100%

SPRING GEAR

(8)

Support: On (Touching Build plate)

Adhesion: BRIM 10mm

Nozzle: 0.4mm 

Speed: 50mm/s

Layer Height: 0.1mm

Infill:100% 

THE BUILD

737_YOKE_CONTROL_HEAD_single_2020-Oct-31

STEP 1

Push the 3 noggins into the body

737_YOKE_CONTROL_HEAD_single_2020-Oct-31

STEP 3

Place the spacer over the shaft,

Secure with screw

STEP 7

Insert both the Pot & Spur Gear into position

Place the yoke shaft assy into position.

Make sure the Pot is in the central position.

STEP 9

Place the yoke onto the end of the yoke shaft,

Place the yoke lock and secure with the screw.

737_YOKE_CONTROL_HEAD_single_2020-Oct-31

STEP 2

Push QTY 2, 6203 Bearings onto the yoke shaft

737_YOKE_CONTROL_HEAD_single_2020-Oct-31

STEP 4

Insert the spring into the eye end of the spring gear

Secure with countersunk screw

STEP 6

Place the 6001 bearing onto the end of the spring gear

STEP 8

Place the two head bodies together and secure with screws

+673 7207616

Patreon:        737DIYSIM

YouTube:      Heli Mech

Facebook:    Boeing738v2

Instagram:    737DIYSIM

Twitter:         737DIYSIM

Watsapp:     +673 7207616

Email: HelenWatersClarke@Hotmail.com

Fancy helping the website

or buying us a thank you beer?