General Information:

STEP:

Wire/connect the components as you go through the build steps
https://031b6b45-11f6-46a7-ab8e-17be9aef4dad.usrfiles.com/ugd/031b6b_f609d62b299146fa865d817b8a82a8da.pdf

STEP:

Print the Qty 4 frames in white PLA, OR print in Black if backlighting is not required and use a white paint pen to highlight the raised text.

STEP:

Spray the 4 parts with black spray paint, apply at least 3 or 4 coats to build the layer thickness. This is required to stop the backlighting from shining through. Once dry, gently sand or file the paint of the raised text.

STEP:

Print all the Action buttons in white PLA

STEP:

Spray the 4 parts with black spray paint, apply at least 3 or 4 coats to build the layer thickness. This is required to stop the backlighting from shining through. Once dry, gently sand or file the paint of the raised text.

STEP:

Insert the 6mm x 6mm led tactile switch into the back of the Action buttons. They should click into place. If you need to remove the switches, you will need a screwdriver to remove the switches from the buttons without damage.

STEP:

Insert the actions buttons complete with tactile buttons into the frame, bend the 4 outer legs over to hold the switch in position.

STEP:

NXI version only
Insert the actions buttons complete with tactile buttons (12) into the frame, bend the 4 outer legs over to hold the switch in position.

STEP:

Insert the encoder into the backplate and secure it with an attachment nut

STEP:

insert the unit into the top orifice

STEP:

Secure with Qty 3, M2.6 x 8mm dome head screws.

STEP:

Place the Volume Knob over the encoder, if the unit is loose, secure with hot glue, or slightly shrink the design to fit.

STEP:

Insert the Propsimwash dual encoder and secure with attachment nut.
ALT: Insert the EC11 dual encoder and hot glue into position.

STEP:

Propsimwash encoder: Install the supplied knobs (Paint black)
EC11 encoder: Print and install the knobs.

STEP:

Install the encoder

STEP:

Install the heading knob on to the encoder

STEP:

Install the Propsimwash encoder and secure with supplied nut.
ALT: Install the EC11 encoder and secure it with hot glue.

STEP:

Propsimwash encoder: Install the supplied knobs (paint black)
EC11 encoder: Printa and install the knobs.

STEP:

Install the 3mm leds with hot glue for backlighting in the Qty 4 holes.

STEP:

Install the action button onto the tactile switches

STEP:

Insert the actions buttons complete with tactile buttons into the frame, bend the 4 outer legs over to hold the switch units into the RHS frame.

STEP:

Insert the encoder into the backplate and secure it with an attachment nut.

STEP:

Insert the unit into the RTHS frame and place the vole knob into the shaft.

STEP:

Secure the backplate with Qty 3, M2.6 x 8mm dome head screws.

STEP:

Insert the Propwashsim encoder into the next orifice and secure it with the supplied attachment nut.
ALT: Install the EC11 encoder and secure it with hot glue.

STEP:

Place the supplied Propsimwash knobs onto the encoder
ALT: EC11 print and fit the knobs.

STEP:

Insert the Propwashsim encoder into the next orifice and secure it with the supplied attachment nut.
ALT: Install the EC11 encoder and secure it with hot glue.

STEP:

Place the supplied Propsimwash knobs onto the encoder
ALT: EC11 print and fit the knobs.

STEP:

Insert the single encoder into the frame, secure with locknut

STEP:

Place the 3d printed knob over the encoder

STEP:

Insert the Propwashsim encoder into the next orifice and secure it with the supplied attachment nut.
ALT: Install the EC11 encoder and secure it with hot glue.

STEP:

Place the supplied Propsimwash knobs onto the encoder
ALT: EC11 print and fit the knobs.

STEP:

Insert the Propwashsim encoder into the next orifice and secure it with the supplied attachment nut.
ALT: Install the EC11 encoder and secure it with hot glue.

STEP:

Install the action button onto the tactile switches

STEP:

Insert the actions buttons complete with tactile buttons into the frame, bend the 4 outer legs over to hold the switch units into the Bottom frame.

STEP:

Place the 4 frames together and secure with Qty 4, M45 x10mm countersunk screws.

STEP:

Place the 10.4" LCD into the unit. The screen will be upside down. The lip will be uppermost.

STEP:

NXI Only: Place the LHS support into position and secure it with Qty 2, M4 x 8mm Dome Head Screws

STEP:

STD Only: Place the LHS support into position and secure it with Qty 2, M4 x 8mm Dome Head Screws

STEP:

Place and secure the RHS support and secure with Qty 2, M4 x 8mm DOme Head screws.

STEP:

Place the support matrix and secure it with Qty 4, M4 x 8mm countersunk screws.

STEP:

Place the LCD driver board into position. Secure with Qty 2, M2.6 x 8mm screws

STEP:

Install the LCD menu board and secure it with QTY 2, M2.6mm x 8mm dome head screws.

STEP:

Place the LCD power board into position and secure it with Qty 2, M2.6 x 8mm screws.

STEP:

Install the Arduino mount and secure with Qty2, M4 x 6mm countersunk screws.

STEP:

Place the Arduino Mega into the mount and secure it with M2.6mm x 8mm screws.