Boeing 737 Motorised Throttle2

Print Guide:

Boeing 737 Motorised Throttle2

(C3) RHS Case

QTY:1
Material: PLA

Colour: D.Grey
Infill:25%
Support: ON - Everywhere

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

R4 Drive Clamp

QTY:1
Material: PLA

Colour: Any
Infill:25%
Support: ON - touching Buildplate

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

R8 Spur Gear 44T

R12 Flaps Detent

QTY:1
Material: PLA

Colour: Metallic Silver
Infill:60%
Support: ON - touching Buildplate

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

R16 Lower Stem (template)

R20 Guide Plate

QTY:1
Material: PLA

Colour: Metallic Silver
Infill:40%
Support: ON - touching Buildplate

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

R24 Flaps Cover

QTY:1
Material: PLA

Colour: D.Grey
Infill:25%
Support: ON - touching Buildplate

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

R1 Throttle Guide Plate

QTY:1
Material: PLA

Colour: D.Grey
Infill:25%
Support: Off

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

R5 Spur Gear 26T

R9 Trim Wheel Slider

R13 Flap HDL

QTY:1
Material: PLA

Colour: White
Infill:25%
Support: ON - touching Buildplate

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

R17 Flaps Stem

R21 Cutoff Lever

R25 Stab Trim Decal

QTY:1
Material: PLA

Colour: White
Infill:15%
Support: ON - touching Buildplate

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

R2 Spur Gear 8T

QTY:1
Material: PETG or ABS (if applying power/heat) PLA for non motorised units

Colour: Any
Infill:25%
Support: Off

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

R6 Hall Slider

R10 Trim Wheel Clamp

R14 Upper Stem (Template)

R18 Stab Trim Decal

QTY:1
Material: PLA

Colour: White (sprayed black and text sanded back to white)
Infill:15%
Support: ON - touching Buildplate

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

R22 Start lever (Template)

R3 Nema Sliding Plate

QTY:1
Material: PETG or ABS (if applying power/heat) PLA for non motorised units

Colour: Any
Infill:25%
Support: ON - Touching Buildplate

Nozzle: 0.4mm
Layer height: 0.2mm
Support Pattern: Concentric
Support Density: 10%
Support Z Distance: 0.2mm
Support X/Y Distance: 1.0mm
Adhesion: Skirt
Print Speed: 50mm/s
Infill Speed: 80mm/s
Support Speed: 60mm/s
Initial Layer Speed:15 mm/s
Number of slower layers: 2
Experimental Conical Support: Active

Print Guide: