
Boeing 737 Saitek Throttle MOD
This page is split into three main sections:
Parts Guide
Print Guide
Build Guide
The ultimate printer I can recommend is the Bamboo Labs X1 carbon with AMS if you have deep pockets. ($1200). It's a massive leap forward in 3D printing, with excellent quality and impressive speeds. Its pretty much press print and go as the software and hardware do the calibration before each print. This printer will not manage the larger parts and you are going to need the CREALITY CR10 v3, which is my second choice of printer.

The unit features:
• Operational Speed Brake Lever
• Dual independent Thrust Levers
• Dual independent Thrust reverser levers utilising potentiometers
• Flap lever with gated guards
• Bell cut out switch
• A/T Disengage switches
• TOGO switches
• Operational parking brake Lever & light
• Operational Fuel Shut Off Levers
General Information:
Parts Guide:

You are going to need the following items to complete this build:
Click Image for Link | Component | Description | Qty |
---|

Print Guide
_PNG.png)
(1) THRUST KNOBS
Printed on end
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(5) FLPAS DECAL
Printed on end
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(9) FLAPS LVR UPPER
Printed on end, Support Structure on.
25% infill
0.1mm Layer Height
0.4mm
_PNG.png)
(13) SPD BRK HANDLE
Printed text up.
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(17) BRK LVR MODDED
Printed on side.
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(21) CUT OFF BODY
Printed on end
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(25) LH END CAP
Printed flat, Countersunk side up.
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(29) SWITCH CAP
Printed with base flat.
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(33) SPRING PLUG
Printed with base flat.
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(2) REV KNOBS
Printed on end
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(6) END PLATE
Printed Flat
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(10) FLAPS LVR LOWER
Printed Flat, round side down. Supports on.
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(14) FLAPS HANDLE
Printed Flat, text up.
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(18) BRK LVR ASSY
Printed flat, supports on.
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(22) CUT OFF LEVER
Printed flat, stud up.
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(26) ADAPTER PLATE
Printed Flat, rim side up. Supports on.
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(30 ) CUTOFF DECAL
Printed Flat, text up.
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(3) BACKPLATE
Printed on flat, countersink holes up
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(7) FLAP ASSY BODY
Printed flat, support structure as req’d.
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(11) REV LVRS
Printed flat, Supports On.
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(15) SPD BRK HANDLE
Printed flat, support structure as req’d.
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(19) BRK LVR CAP
Printed on flat, countersink holes up
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(23) CUTOFF HANDLE
Printed Flat, text up
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(27) WEDGE
Printed on end, Supports On.
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(31) STAB TRIM DECAL
Printed flat, text up.
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(4) BRACKET
Printed flat
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(8) FLAP DETENT
Printed flat, noggins face up. Support structure on.
25% infill, 0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(12) SPACER BODIES
Printed flat, Support structure on.
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(16) TOP PLATE
Printed flat.
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(20) CENTRE BODY
Printed on side
25% infill
0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(24) LH BODY
Printed flat, Support structure on.
25% infill, 0.1mm Layer Height
0.4mm Nozzle
_PNG.png)
(28) RH BODY
Printed flat, Support structure on.
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)
_PNG.png)
(32) PARK BRAKE DECAL
Printed flat, text up
25% infill
0.1mm Layer Height
0.4mm Nozzle (0.2mm Recommended)

Build Guide



